“Your walls form the foundation of your home. The weather out there will not be nice for the exterior walls of your house. It isn’t enough to paint your wall to make it waterproof. After dealing with rain, snow, wind, dust, and heat of the outside environment, the paint will begin peeling off.”
Thus, waterproofing is the best way to ensure that your walls are protected and retain your house’s longevity. At the same time, it is vital to reduce your frequent renovation cost. So, here are some of the simple steps for providing effective waterproofing solutions to your home.
Damp carpets and beneath wall coverings can be the most prominent place for mold and mildew growth. Finishing a basement without first dealing with the moisture problems can make health conditions worse and lead to significant damage. Interior waterproofing systems, installed by a professional contractor, can keep the moisture away throughout the home.
Step 1: Properly expose the outside part of the wall
To start with waterproofing your exterior walls, make sure it is properly exposed to work on. Your house walls possess a lot of dirt, which creates an additional layer over the wall. Get rid of all the filth and dust from the walls. And before doing so, remove all the drainage pipes and the old field tiles to get proper access to every corner and area of the wall.
Step 2: Thoroughly clean the walls
A lot of dust and dirt is carried by air and sticks to the outer part of the wall. To ensure the efficiency of the whole process, you need to clear off the debris and dust thoroughly. The dirt and debris can be cleaned by using a broom, brush, or scraper. Then use a power washer to finish it all off.
Step 3: Check out for the cracks and fill them up
Cracks and holes can develop on the exterior walls over time. Follow up the cleaning process with a thorough finding of all the cracks and holes on the wall. Simply fill them up with cement.
Most of the homeowners get worried about cracks in the foundation. But the fact is, not all foundation cracks affect the home’s structural integrity. Sometimes cracks can be caused by shrinkage during the concrete curing process. These unsightly, non-structural shrinkages, commonly known as hairline cracks, don’t put your home in immediate danger. But on the other hand, structural cracks are serious business.
All over the internet and TV you find websites and programs with step-by-step guides of DIY foundation repair. But the truth is that a foundation should not be experimented on in a DIY project. Foundation repair requires years of experience and specialized tools. When it comes to foundation repair, contact a foundation repair expert.
It is possible to seal the cracks with a cement mixture. Remove the loose cement from the wall before applying the cement.
Step 4: Add a layer of cement waterproofing sealer
If you want to make sure your wall is waterproof, you need to apply cement. After applying the cement in the crevices, let it dry and then apply the waterproof paint seal. Allow it to be dry.
Step 5: Pick the right water-proofer
There are many products in the market that are waterproof. You need to choose the right one for the wall. The water-proofer should be selected based on whether the wall is concrete or silicate.
You can choose between a silicate-based concrete seal or a concrete waterproof coating. You can add strength to your walls with a plaster waterproof Additive.
Step 6: Apply the water-proofer
Use a roller or brush to apply the water-proofer on the walls. If you want to apply more than one layer, give a thin coat. Allow the first coating to dry and then add the second.
Step 7: Apply tar and heavy-duty membrane
“If you want to add more strength to the layer, you need to use a tar-based pitch after you’ve dried the cement. It should be applied on your wall.”
After that, you need to apply a heavy-duty plastic or rubber Membrane, which will ensure the proper care of your walls
Step 8: Consider adding gravel
If you want to lay the drainage pipes, you need a proper base below the footer. The drainage pipes will be supported by a 34-inches gravel base. Gravel provides enhanced protection.
You need to lay the drainage pipe-cover along with gravel. Next to the footer, level the position of the gravel and back-fill it. The pipe should be covered for at least 3-inches.
Step 9: Add a fabric barrier
The fabric barrier should be secured with the perforated pipe. Ensuring a fabric barrier is going to keep your system free of dirt. Then back-fill the trench and build the top of the dirt relatively high and let it settle for a while. Slope the ground away from the walls for the run-off after youTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkia
Conclusion:
“Your home gets a new life and strength when it’s waterproof. Magicrete can help you find good solutions for your walls. At a very low and affordable price, Magicrete can help you with your outdoor needs.”
“It’s not like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it”
